A3 Industries Turns the 10mm & .45 Stribog into a Bullpup

By Eric B •
a3 industries turns the 10mm 45 stribog into a bullpup

The Grand Power Stribog has earned its reputation the hard way. At the first-ever IPSC PCC/Mini Rifle World Shoot, held in Znojmo, Czech Republic, in May 2025, the overall winner was Slovakia's Pavol Zencar, and as I wrote in shooting the Stribog SP9A3G, Team USA achieved significant success, but number one on the podium was Pavol with his Stribog. A3 Industries has now taken the platform in a very different direction with a bullpup conversion kit, though it will not fit the 9mm that won the World Shoot.

a3 industries turns the 10mm 45 stribog into a bullpup

The kit is for the 10mm Stribog SP10 and the .45 ACP Stribog SP45 only. It replaces the factory lower receiver, which takes about ten minutes, and turns the carbine into a bullpup measuring just 16 in (40.6 cm) overall. The conversion lower weighs 2.5 lb (1.13 kg) on its own and about 6.5 lb (2.95 kg) with the upper fitted.

a3 industries turns the 10mm 45 stribog into a bullpup

A3 has fitted the important parts before it leaves the shop. A RAVE-140 trigger with a 3.5 lb (1.6 kg) pull comes pre-installed, modified specifically for this conversion, so you cannot swap in a different trigger. There is also a Lingle Industries enhanced bolt catch, an ambidextrous selector and a textured paddle magazine release. The grip is A3's Xeno reduced-angle AR grip, and the butt plate is a polymer CQB design with a rubberized pad.

a3 industries turns the 10mm 45 stribog into a bullpup

Now for the part that made me look twice at the photos. A 16-inch bullpup in 10mm or .45 is tiny, and on a gun this short, the muzzle sits very close to where your support hand naturally wants to go. That is a fine way to shoot a finger or a hand off if you do not pay attention. A3 includes an optional hand stop to give the support hand a forward reference point, and on this gun I would treat it as mandatory, not optional. Or use the longest suppressor you can find.

a3 industries turns the 10mm 45 stribog into a bullpup

The lower is machined from 6061 aluminium with a low-gloss black anodized finish and is made in the USA. Since the Stribog's lower is not the serialized part, the conversion kit is not a firearm and ships directly to your door. Fitting it does make your Stribog a short-barreled rifle, though, so US buyers need to check federal, state and local rules before they install it.

a3 industries turns the 10mm 45 stribog into a bullpup

A3 Industries Stribog SP10/SP45 Bullpup Conversion Kit - the details:

  • Compatibility: Grand Power Stribog SP10 (10mm) and SP45 (.45 ACP)
  • Not compatible with 9mm Stribog models
  • Overall length assembled: 16 in (40.6 cm)
  • Weight: 2.5 lb (1.13 kg) lower only, about 6.5 lb (2.95 kg) with upper
  • Material: 6061 aluminium, low-gloss black anodized
  • Trigger: RAVE-140, 3.5 lb (1.6 kg), modified for this kit and not swappable
  • Lingle Industries enhanced bolt catch
  • Ambidextrous selector and textured paddle magazine release
  • Xeno reduced-angle AR grip
  • CQB butt plate with rubberized pad
  • Hand stop included
  • Installation: about 10 minutes
  • Not a firearm, ships direct; installed configuration is an SBR
  • Limited run of 100 units
  • Made in the USA, lifetime warranty
  • SKU BPC-STR10, $999.95

a3 industries turns the 10mm 45 stribog into a bullpup

Only 100 kits have been made.

Would you turn your Stribog into a bullpup, or keep it as a conventional carbine?



If this post has you ready to hit the range, head over to gunranges.com - a free directory to help you find shooting ranges near you, wherever you are in the United States.